← Back to products

45 steel, quenched and tempered

45 Steel Q&T Ground Round Bar

Quenched-and-tempered ground bar for orders that need balanced mechanical properties and room for downstream machining.

Inquire about this product
45 Steel Q&T Ground Round Bar
45 steel, quenched and tempered

SPECIFICATIONS

45 Steel Q&T Ground Round Bar: standard specification

Standard specification. Other sizes, tolerances and chrome layers are quoted against your drawing.

GradeGrade 45 to GB/T 699-2015 · comparable, for reference only: C45, S45C, SAE 1045
DiameterØ8–140 mm (Q&T from Ø8)
ToleranceØ8–11: −0.02/−0.05 mm · from Ø12: 0/−0.02, −0.01/−0.03 or −0.02/−0.05 mm
HardnessSurface hardness HRC25–28 or HRC28–32 (chosen per order); grade 45's limited hardenability leaves the core softer than the surface
Surface roughnessRa ≤ 0.8 μm
Straightness≈ 0.1 mm/m from Ø25 · ≈ 0.2 mm/m below Ø25
Length & cuttingFull bars 4 m, 6 m, 7.5 m or 8.1 m; CNC saw cut to length from 200 mm (≈ 3 mm allowance), ends left as sawn
Certificates & testingSteel mill certificate for each heat, forwarded unaltered; foreign grades named here are for reference only; third-party testing commissioned per order on request
TYPICAL APPLICATIONS

Loaded shaft components; mechanical transmission parts; stock for precision machining.

SELECTION NOTE

If the final working surface requires hard chrome, confirm whether to select a chrome-plated product or reserve the part for downstream surface treatment.

ABOUT THIS BAR

45 Steel Q&T Ground Round Bar: how it is made and when to choose it

A grade 45 steel bar, induction quenched and tempered to a surface hardness of HRC25–28 or HRC28–32 (you choose the range per order), then roll straightened, centerless ground and polished, all in the Yixin workshop.

Grade 45 has limited hardenability, so the core is softer than the surface; this is normal for the grade, and the hardness we state is surface hardness. For a harder core, see our 40Cr Q&T bar (HRC28–35).

Test evidence on a July 2026 sample bar: Jiangsu Yinshi Inspection & Testing (CNAS L18906) measured a surface hardness of HV10 292.6 / 297.2 / 298.3 (about HRC 29; conversion is approximate), core hardness HRC 21.6 / 22.0 / 21.9, tensile strength 863 MPa and elongation 23.0%. Jiangsu Third Party Measurement Technology (CNAS L11694) measured Ra 0.384 μm and roundness 0.004–0.006 mm. Results apply to the sample tested.

PROCESS ROUTE

How this bar is made

Dashed steps are done by long-term partner plants to Yixin's specification; all others run in the Yixin workshop.

Yixin workshopLong-term partner plant, to Yixin's specificationAll products can be CNC-sawn to length

RELEVANT PROCESS CAPABILITY

Technical baselines relevant to this product route

01-0.02 to -0.05 mmcommon tolerance
020 to -0.02 mmoptional tolerance
03HRC25–28 / 28–3245 steel Q&T surface hardness

Standard values for 45 steel Q&T ground bar. Final values are fixed on the confirmed drawing, specification and order.

PRODUCT FAQ

Questions buyers ask about the 45 Steel Q&T Ground Round Bar

01Why is the core hardness lower than the surface?

Grade 45 has limited hardenability, so after quenching and tempering the core stays softer than the surface. This is expected for the grade. The hardness we state and check is surface hardness (HRC25–28 or HRC28–32, chosen per order). On our July 2026 sample the core measured HRC 21.6–22.0. If you need a harder core, choose 40Cr Q&T (HRC28–35).

02Which hardness range should I choose?

Choose HRC25–28 or HRC28–32 on the order. Tell us the application and the machining that follows, and we confirm the range in the quotation.

03Do you have test reports for this bar?

Yes. Two July 2026 reports on a sample bar are on our Quality page: composition, hardness and tensile test by Jiangsu Yinshi Inspection & Testing (CNAS L18906), and dimensions and roughness by Jiangsu Third Party Measurement Technology (CNAS L11694). Results apply to the sample tested.

04What is the smallest diameter for Q&T?

For grade 45, Q&T starts from Ø8 mm; the range is Ø8–140 mm.

SERVICE

Export terms

How standard orders are handled. Volume and special requirements are written into the quotation.

Minimum order
1 t per order (different sizes can be combined); 20–50 kg sample orders (the sample fee is refunded with your order; samples go by international express, freight paid by the buyer)
Lead time
Cut-to-length from stock 3–5 days · non-standard diameters 7–10 days · custom heat treatment 10–20 days · 42CrMo 7–10 days, plus sea-freight booking; thicker chrome layers are quoted per order
Trade & payment
FOB Shanghai or Ningbo · T/T only, 50% deposit, balance before shipment (no L/C)
Packing
Export: bars wrapped in bubble film and packed in wooden cases; domestic: bubble film and cotton-rope ties. No steel straps on finished bars, so the surface is not marked; your brand can be printed on the packing
Documents
Commercial invoice, packing list and steel mill certificate for each heat (forwarded unaltered); certificate of origin arranged per order; third-party inspection on request
Response
Quotation reply within one working day

Inquire about 45 Steel Q&T Ground Round Bar

Send diameter, length, quantity or a drawing. We reply with grade, tolerance, chrome thickness and lead time.

Prepare RFQ